manualshive.com logo in svg

Bauer Rainstar TX Plus E, Operating Manual, Page: 26 / 92

Share
Download
Bauer Rainstar TX Plus E Operating Manual Download Page 26

 
 

Operating manual for 

BAUER RAINSTAR

 

Series TX Plus 

18 

But note:

 

When the cart is lifted and in the shut-off position, the gear-shift lever is held in “0” position and shifting is 
impossible!  If the PE-pipe is stretched you have to slacken it first, before engaging the next gear  
 

 

 

 

 

Move the gear shift lever from a gear stage to the middle 
position.  A spring presses the gear shift lever up and 
prevents fast reversing of the reel and PE-pipe by means of 
the band brake.  By pushing the gear shift lever down very 
slowly you release the brake and slacken the PE-pipe.     

 

           

 

 

 

 

Afterwards you can change into the required gear.  

 

PTO DRIVE

 

 

 

 

 

If required, you can rewind the PE-pipe with the tractor and a 
PTO shaft.  Move the gear shift lever to zero position.  A 
spring presses the gear shift lever into the locking recess.  In 
this position the band brake is released. This gear shift lever 
position serves also for PE-pipe pull-off.        

 

Summary of Contents for Rainstar TX Plus E





























































































Reviews:

No comments