manualshive.com logo in svg

Bauer Rainstar TX Plus E, Operating Manual, Page: 36 / 92

Share
Download
Bauer Rainstar TX Plus E Operating Manual Download Page 36

 
 

Operating manual for 

BAUER RAINSTAR

 

Series TX Plus 

28 

6.6  STOP - SENSOR 

 
 
The machine can only work if the stop sensor is activated or in operating position.  
 

   Operating position 

 

 

 

Shut-off position  

 
 
 
 
 
 
 
 
 
 
 
 

The Stop - Sensor has three functions: 

 
1. 

    Reset for the laid-down PE-pipe length: 

 

When operated the laid-down pipe length is set to zero. 

2. 

Post irrigation:  
If the post-irrigation procedure is carried out at the end of the run (0 m laid-down PE-pipe length) the post-
irrigation function is activated first and then the  

ECOSTAR

 is shut-off. 

 

In the standard program the post-irrigation is activated 8m before the irrigation ends. 

3. 

Prevents pulses to the regulating motor. 

 

After the stop sensor is activated, no pulses are passed on to the regulating motor. 

 
Press the key  

MENU 

2 x, to get to the display of menu 3. Her it shows if the speed sensors are working . The sign                 

 
shows if a magnet activated the two speed sensors. 
 
Line four shows if motors 1 and 2 are switched off after they have reached their mechanical stop. 
If sign                     shows and one motor has not  
reached its end position there is a blockage on the inside of the turbine ( MOTOR 1 ) or the valve( MOTOR 2 ). 
The motor switches off when the power consumption exceeds 4,7 ampere and               appears on the display. 
 
If the display shows a flashing MOTOR 1 it means that the motor is running 

 
SPEED      30.0m/h    
DOSE      22 mm 
TIME   14:10 STOP 7:43

STATUS MOTOR 1

                  

 

 
If the display shows a flashing MOTOR 2 it means that the motor for the shut off valve is running. 

 
SPEED      30.0m/h    
DOSE      22 mm 
TIME  14:10 STOP 7:43

STATUS MOTOR 2

                  

 

 

By pressing the key PROG/POWER ON 

or the PE-Pipe is laid out, the electronics is activated again.  

 
The battery is charged only if the electronics is activated. There is no charging when in standby.  
 
 
 
 

Summary of Contents for Rainstar TX Plus E





























































































Reviews:

No comments