background image

*1: When biodiesel fuel is used, change the fuel filter cartridge, fuel hose and clamp bands with new
ones at intervals half of the usual ones.
*2: Consult your local Baroness Dealer or local KUBOTA Dealer for this service.
The items above (*3 marked) are registered as emission related critical parts by KUBOTA in the
U.S. EPA nonroad emission regulation.
As the engine owner, you are responsible for the performance of the required maintenance on the
engine according to the above instruction.
Please see the Engine's Warranty Statement in detail.
The items listed above other than *3 marked are not necessary to keep the emission-related
warranty valid.
Failure to perform the maintenance will cause problems that will significantly degrade the engine
performance.
*4: Refer to the Engine's Owner's Manual.
*5: Refer to the Battery's Owner's Manual.
The values for consumables are not guaranteed.
Replace the steering cylinder hoses every 2 years.

Adjusted Value

Fan belt

10 mm (0.39 in)

Belt slack

Mower stabilizer spring

#1 - 5

140.0 mm (5.51 in)

Total length of spring

Location of stopper nut

LH62

#1, 4, 5

15.0 mm (0.59 in)

 

#2, 3

40.0 mm (1.57 in)

 

LH52

#1, 4, 5

15.0 mm (0.59 in)

 

30.0 mm (1.18 in)

With grass catcher

#2, 3

40.0 mm (1.57 in)

 





Maintenance

LM551B

Maintenance

Page 5-7

Maintenance Schedule

Summary of Contents for LM551B













































































































































































Reviews: