9. Input
To activate the single channel 3D mode select:
MENU
>
Input
>
3D
>
Frame Sequential – Single Channel
Possible sources: DisplayPort, HDMI, dual-link DVI, 5-cable analog (up to 210 MHz), DVI analog (up to 170 MHz), SDI (up to 150
MHz).
With the “Invert 3D sync out” setting the content can be switched between the left and right eye of the user.
The “Field dominance” setting has only effect in the 3D mode: Frame sequential
→
Single channel (in all other
modes this setting is grayed out). Furthermore, the input frequency must be equal or lower than 100 Hz (50
Hz per eye). In case the input frequency is higher than 100 Hz (50 Hz per eye, 59.94 & 60 Hz in practice), the
“Field dominance” setting has no effect.
Single 3D channel - Full resolution - other formats
Contains Frame packing and Line Alternating (3G-B).
To activate the single channel 3D mode select:
MENU
>
Input
>
3D
>
Frame packing (FHD3D)
or
MENU
>
Input
>
3D
>
Line Alternating (3G-B)
(only for SDI input)
Single 3D channel - Half resolution
3D content is distributed by one 3D source by means of “Side By Side”, “Top Bottom” or “SENSIO
®
Hi-Fi 3D”..
To activate this single channel 3D mode select one of the three options:
MENU
>
Input
>
3D
>
Side-By-Side (Half)
MENU
>
Input
>
3D
>
Top-and-Bottom (Half)
MENU
>
Input
>
3D
>
SENSIO
®
3D Decoder - FFC
(only on 3D input)
Example: A 3D HDMI source with a Side by Side video of 60 Hz results in a 60 Hz video per eye.
In this mode the 3D Input Module also generates the 3D sync.
Possible sources: Display Port, HDMI, DVI , SDI input.
Dual 3D channel - Two parallel 3D content streams
3D content is applied to the projector via two input ports. One port is used for content of the left eye, the other port for the right eye.
Example: Two parallel DVI streams of 60 Hz: DVI cable 1 is connected with the DVI port of the projector. DVI cable 2 is connected
via a HDMI converter cable with the HDMI port of the 3D Input Module. To switch the HDMI/DP input to HDMI, select
MENU
>
Input
>
Advanced Settings
>
HDMI/DP
>
HDMI
.
For the second source the correct type has to be selected as follows with the
fi
rst source already selected :
MENU
>
Input
>
3D
>
Second Input
>
“select corresponding slot number”
The 3D Input Module is activated for Dual 3D channel:
MENU
>
Input
>
3D
>
Frame Sequential – Dual channel
Possible sources: 2 x DVI , 2 x SDI. If two 3D Input Modules are installed: 2 x HDMI or 2 x DisplayPort.
SENSIO
®
Hi-Fi 3D
1
2
1
2
3
4
3
4
2
1
2
1
4
3
4
3
1
1
2
2
3
3
4
4
1
1
2
2
3
3
4
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
(1)
(2)
(4)
(5)
(6)
(7)
(3)
Image 9-58
SENSIO
®
HI-FI 3D decoding
104
R5905303 HDQ 2K40 02/03/2015
Summary of Contents for HDQ--2K40
