R5906848 /04
DP2K SLP Series
340
Code 6050:
“
dmd - temperature hardware protection warning
”
Situation
Solution
DMD temperature low.
Make sure that the ambient temperature is within specs. Let the projector
acclimate to the normal room temperature which should be higher then 10°
C (50°F) and lower then 35°C (95°F). Do not ignite the lamp, otherwise
there is a risk for condensation.
DMD temperature high.
Check all cooling systems: small dust filter, large dust filter, air extraction
system, etc.
Code 6061:
“
+24v - voltage high
”
Situation
Solution
Malfunction Cinema Control
board or SMPS board.
Put the projector in Stand-By mode, remove the Light Source and the
Cathode Fan assembly to access the Signal Backplane connections with
the SMPS wires (reference 6 Image 25-82). Then, measure on the Signal
Backplane the +24V voltage on pin 9, 10, 11 or 12 of the connector with
the black wires coming from the SMPS board. See Image 25-82.
If the measured voltage is about 24V then replace the Cinema Control
board. See service manual chapter
“
, page 217. Otherwise replace the SMPS board. See service
manual chapter
Switch Mode Power Supply (SMPS)
”
, page 39.
Note
: To remove the Light Source see service manual chapter
”
, page 59. To remove the Anode Fan assembly
see service manual chapter
, page 84.
Note
: The projector must be in Stand-By mode otherwise no voltages are
generated by the SMPS board.
13
1
+24V
14
2
15
3
16
4
17
5
+VTEC
GND
18
6
19
7
20
8
21
9
22
10
++12V
23
11
24
12
13
13
24
24
6
Image 25-82
Code 6062:
“
+24v - voltage too low
”
This error code is probably preceded by the warning code 6063:
“
+24v - voltage low
”
. The same
troubleshooting table can be applied.
Summary of Contents for DP2K SLP Series
