background image

A-5

Vegetables  are  generally  easy  to  cook  on  the  grill.  The
Secondary Cooking Rack makes it convenient because you
can still use the main cooking area while the vegetables are
suspended  above  the  grids.

Pre-cook  hard  vegetables  by  briefly  boiling  or  microwaving
them before cooking on the grill. Wrap vegetables in a double
thickness  of  foil  to  protect  them  while  cooking  on  the  grill.
Then,  remove  the  foil  if  desired,  10-15  minutes  before  the
end of cooking, brush vegetables with butter or oil and finish
cooking.

Guide  to  Using  the  Secondary  Cooking  Rack

The  Secondary  Cooking  Rack  can  be  used  for  purposes
other  than  just  the  obvious.  Consider  using  the  rack  for
warming  French  bread,  garlic  bread,  croissants  or  even
bagels.

A  small  whole  fish  wrapped  in  foil  also  cooks  well  on  the
Secondary  Cooking  Rack.  Parcels  of  seafood  such  as
scallops,  prawns  and  sliced  fish  fillets  prepared  in  a  sauce
and portioned  into small  foil wraps  cook well  this way,  too.

Slow Cooking with a Rotisserie

Rotisserie  cooking  produces  foods  that  are  moist,  flavor-
ful  and  attractive.  The  rotisserie  system  is  most  com-
monly  used  for  cooking  meat  or  poultry  and  is  designed
to  cook  food  slowly.

The  cooking  times  on  a  rotisserie  will  be  approximately  the
same  as  for  oven  cooking.

Balancing the Food

In  rotisserie  cooking,  balancing  the  food  is  of  utmost
importance.  The  rotisserie  must  turn  evenly  or  the  stop-
ping  and  starting  action  will  cause  the  food  to  cook
unevenly  and  possibly  burn  the  heavier  side.

The  easiest  foods  to  balance are  those  of  uniform  shape
and texture. To test if the food is balanced correctly when
secured, place the ends of the rotisserie spit loosely in the
palms of your hands. If there is no tendency to roll, give the
spit a  quarter turn.  If it  is still  stable, give  it a  final quarter
turn.  It  should  rest  without  turning  in  each  of  these  posi-
tions.  It  can  then  be  attached  to  your  grill.

Food Preparation

When  preparing  poultry,  truss  the birds  tightly  so  that  wings
and drumsticks are close to the body of the bird. The cavity of
the bird may be stuffed prior to this. Pull the neck skin down
and, using a small skewer, fix it to the back of the bird. Push
the rotisserie spit through lengthwise, catching the bird in the
fork  of  the  wishbone.  Center  the  bird  and  tighten  with  the
holding  forks.  Test  the  balance  as  described  before.

A  rolled  piece  of  meat  requires  the  rotisserie  skewer  to  be
inserted  through  the  center  of  the  length  of  meat,  then  se-
cured  and  balanced.

For  meats  that  contain  bones,  it  is  best  to  secure  the  rotis-
serie  skewer  diagonally  through  the  meaty  sections.  If  pro-
truding bones  or wings brown  too quickly, cover  with pieces
of  foil.

Guide  to  Rotisserie  Cooking

Preparing to Smoke

Smoking gives food a distinctive, delicious flavor. You will find
a  variety  of  wood  chips  available  for  use  in  smoking  grilled
foods. Pre-soaking of wood chips may be required so read
and  follow  the  manufacturer's  instructions  for  preparing
smoking  chips  prior  to  use.

Note:

 It is our experience that many smoking chip products

do  not  actually  produce  a  smoke  but  instead  infuses  the
food  with  flavor.  Please  read product  labels  carefully  and  if
in  doubt,  ask  your  retailer  for  details.

Using A Smoker Box

There  are  many  optional  smoker  boxes  available  for  pur-
chase.  Follow  these  guidelines  and  always  refer  to  the
label  of  your  smoking  chips  for  specific  directions.

Raise  your  Grill  Lid  and  light  the  grill.  Lower  the  Grill  Lid
allowing  your  grill  to  reach  the  desired  cooking  tempera-
ture  for the  food you  are grilling.  Fill your  smoker box  with
your  prepared smoking  chips. Dried  herbs  and spices  may
also  be  added  to  produce  different  flavors.  W ear  a  flame
retardant BBQ Mitt and place your smoker box on a Cook-
ing Grid or Flame Tamer directly above a lit grill Burner. The
heated  smoking  chips  will  flavor  your  foods.

Tips for Smoking

You  can  reduce  the  strength  of  the  smoke  flavor  by  only
smoking for half or three quarters  of the cooking time. The
heat  required  for  smoking  is  normally  LOW  to  MEDIUM.

Foods  naturally  high  in  oils  lend  themselves  well  to  smok-
ing,  while  drier  foods  benefit  from  a  marinade.

Guide  to  Smoking

Tuna  steaks,

  marinated  in  Asian  flavors  of  sesame

oil,  soy  sauce  and  sherry.

Pork  fillets,

  rubbed  with  ginger,  orange  rind  and

brushed  with  maple  syrup.

Mussels,

  brushed  with  lemon  rind  and  chili  oil.

Lamb  cutlets,

  marinated  in  virgin  olive  oil,  lemon,

oregano  and  black  pepper.  The  same  marinade  can
be used  for a  whole leg  or rack  of lamb.

Chicken, 

boneless  chicken  pieces—especially  sliced

breasts.

Fish, 

sliced  fillets  of  firm  fish,  assorted  seafood  such

as  prawns,  scallops  and  calamari.

Pork, 

sliced  fillets,  diced  or  minced  pork,  sliced  leg

steak,  sliced  chops.

Beef, 

sliced  fillet,  rib-eye,  round,  rump,  sirloin.

Lamb, 

sliced  fillet,  round,  loin.

Summary of Contents for Grand Turbo B3810ALP













































Reviews: