background image

24

USE  AND  CARE  INSTRUCTIONS

CORRECT  LP  GAS  TANK  USE

The  LP  Gas  tank  must  be  constructed  and  marked  in
accordance  with  the  Specifications  for  LP-Gas  Cylinders
of  the  U.S.  Department  of  Transportation  (D.O.T.)  or  the
National  Standard  of  Canada,  CAN/CSA-B339,  Cylinders,
Spheres  and  Tubes  for  Transportation  of  Dangerous
Goods,  and  Commission;  as  applicable.

The  LP  Gas  tank  must  have  a  shutoff  valve,  terminating
in  an  LP  Gas  supply  tank  valve  outlet,  that  is  compatible
with  a  Type  1  tank  connection  device.  The  LP  Gas  tank
must  also  have  a  safety  relief  device  that  has  a  direct
connection  with  the  vapor  space  of  the  tank.

The  tank  supply  system  must  be  arranged  for  vapor
withdrawal.

The  LP  Gas  tank  must  have  a  collar  to  protect  the  tank
valve.

Never  connect  an  unregulated  LP  gas  tank  to  your  gas
grill.  The  gas  regulator  assembly  supplied  with  your  gas
grill  is  adjusted  to  have  an  outlet  pressure  of  11"  water
column  (W.C.)  for  connection  to  an  LP  gas  tank.  Only
use  the  regulator  and  hose  assembly  supplied  with  your
gas  grill.  Replacement  hose  and  regulator  assembly
must  be  identical  to  those  listed  in  the  parts  list  of  this
Operator's  Manual  as  specified  by  Grand  Hall.

Have  your  LP  Gas  dealer  check  the  release  valve  after
every  filling  to  ensure  it  remains  free  of  defects.

Always  keep  LP  Gas  tank  in  upright  position.

Do  not subject  the LP Gas tank to excessive  heat.

Never  store  an  LP  Gas  tank  indoors.  If  you  store  your
gas  grill  in  the  garage  always  disconnect  the  LP  Gas
tank  first  and  store  it  safely  outside.

LP  Gas  tanks  must  be  stored  outdoors  in  a  well-
ventilated  area  and  out  of  the  reach  of  children.

Disconnected  LP  Gas  tanks  must  not  be  stored  in  a
building,  garage  or  any  other  enclosed  area.

The  regulator  and  hose  assembly  can  be  seen  by
opening  the  cart  or  island  doors.  They  must  be  inspected
before  each  use  of  the  grill.  If  the  hose  is  damaged  in
any  way,  it  must  be  replaced  prior  to  using  the  grill  again.

Any  attempt  to  convert  the  grill  from  one  fuel  type  to
another  is  extremely  hazardous  and  will  void  the  war-
ranty.

Never  light  your  gas  grill  with  the  lid  closed  or  before
checking  to  ensure  the  burner  tubes  are  fully  seated  over
the  gas  valve  orifices.

Never  allow  children  to  operate  your  grill.  Do  not  allow
children  or  pets  to  play  near  your  grill.  Always  supervise
children  and  pets  if  they  are  in  the  vicinity  of  the  unit.

!

    WARNING

!

Keep  fire  extinguisher  readily  accessible.  In  the
event  of  a  oil/grease  fire,  do  not  attempt  to  extinguish
with  water.  Use  type  B  extinguisher  or  smother  with
dirt,  sand  or  baking  soda.
In  the  event  of  rain,  turn  off  the  burners  and  gas
supply.  Wait  for  the  grill  to  cool,  and  then  place  a
cover  on  it.
Use  your  grill  on  a  level,  stable  surface  in  an  area
clear  of  combustible  materials.

LP  Gas  grill  models  are  designed  for  use  with  a  standard
20  lb.  Liquid  Propane  Gas  (LP  Gas)  tank  (sold  sepa-
rately). 

Never 

connect  your  gas  grill  to  an  LP  Gas  tank

that  exceeds  this  capacity.  A  tank  of  approximately  12
inches  in  diameter  by  18-1/2  inches  high  is  the  maximum
size  LP  Gas  tank  to  use. 

You  must  use  an 

"

OPD"  gas

tank  which  offers  a  listed  Overfill

 

Prevention  Device.

This  safety  feature  prevents  tank  from  being  overfilled
which  can  cause  a  malfunction  of  the  LP  Gas  tank.

Do  not  leave  grill  unattended  when  in  use.

Do  not  move  the  appliance  when  in  use.

Allow  the  grill  to  cool  before  moving  or  storing.

Do  not  use  your  grill  as  a  heater.

Use  your  grill  at  least  3  feet  away  from  any  wall  or
surface.
Use  your  grill  3  feet  away  from  any  combustible
objects  that  can  melt  or  catch  fire  such  as  vinyl  or
wood  siding,  fences,  overhangs  (See  Diagram  Be-
low),  or  any  other  sources  of  ignition;  including  pilot
lights  and  live  electrical  appliances.
Do  not  use  your  grill  under  any  overhead  combus-
tible  construction.
Never  use  your  gas  grill  in  a  garage,  porch,  shed,
breezeway,  or  any  other  enclosed  area.
Never  use  your  gas  grill  on  a  balcony,  deck,  or  patio
above  the  ground  floor  of  your  home.
In  windy  conditions,  always  position  the  front  of  the
grill  to  face  oncoming  wind  to  reduce  heat  and
smoke  blowing  in  your  face,  and  to  prevent  potential
hazards  to  yourself  and  the  grill.

(for  B3810ALP/NG  &  BAI10ALP/NG  Models)

!

Do  not  store  a  spare  LP-Gas  tank  under  or  near  this
appliance.
Never  fill  the  tank  beyond  80  percent  full;  and
If  the  information  in  "(a)"  and  "(b)"  is  not  followed
exactly,  a  fire  causing  death  or  serious  injury  may
occur.

A.

B.
C.

    WARNING

!

Use  of  alcohol,  prescription  or  non-prescription  drugs
can  impair  your  ability  to  properly  assemble  and  safely
operate  your  grill.

Never 

use  charcoal  or  lighter  fluid  in  this  grill.

This  grill  is  not  intended  to  be  installed  in  or  on
recreational  vehicles  and/or  boats.

The  grill  is  not  intended  for  commercial  use.

WIND
DIRECTION

3ft.

3ft.

Summary of Contents for Grand Turbo B3810ALP













































Reviews: