manualshive.com logo in svg

B&D Controll-A-Door R, Instruction Manual

Share
Download
B&D Controll-A-Door R Instruction Manual Download Page 21

SECTION 5 - MAINTENANCE

5.1  Maintenance

The Service LED will indicate the requirement for service
and/or adjustment. Whilst the Service LED is illuminated
the courtesy light will flash five times each time the door
is operated until the Service LED is reset. 

To reset the Service LED when the door is serviced,
reprogram the Door Travel Limits and the Door Travel
Force – on completion of this programming the Service
LED will go out.

Whilst your opener does not require any periodic maintenance, the door that it is fitted to does. Your garage door is
a large, heavy, moving object and should be tested regularly to ensure it is in good condition. A poorly maintained
door could cause fatal or serious injuries.

To ensure long and trouble free life of your opener the following is recommended:

5.2  Monthly

•

Disengage the opener and manually operate the door. The door must be smooth to operate by hand, and
operating force on the bottom rail should not exceed 200 Newtons (20kg) force.

•

Each month check that the opener reverses when the door contacts a 40mm high object placed on the floor. 
(AS3350). Refer to Testing the Safety System.

If the door does not operate smoothly, call your nearest Authorised Dealer.

5.3  Yearly

•

We suggest that you contact your nearest Authorised Dealer to perform annual door service.

Warning:

Failure to maintain your garage door may void the warranty on your garage door 
opener.

Record any services in the following table to assist in any warranty service.

Date

Service Performed By

Signature

Amount

Invoice No. 

Frequently examine the installation, in particular cables, springs and mountings, for 
signs of wear, damage or imbalance. Do not use if repair or adjustment is needed 
since a fault in the installation or an incorrectly balanced door may cause injury.

AS3350

Adjustments should only be carried out by experienced persons, as this function can 
be dangerous if not performed under strict safety procedures.

©Copyright 2003

21

Part No 059778

SERVICE

POWER

For Product Support contact 1800 636 407

Patents Apply

Service
Indicator
LED

Summary of Contents for Controll-A-Door R





























Reviews:

No comments

Brands by name

Popular brands

Load more brands