manualshive.com logo in svg

B&D Controll-A-Door R, Instruction Manual

Share
Download
B&D Controll-A-Door R Instruction Manual Download Page 20

4.11  Auxilliary Output

The radio receiver of this garage door opener can be used to operate other devices. Connect an interface cable kit
to the J8 Connector on the garage door opener and the device to be controlled (eg an alarm panel, security lights,
etc).

Program a spare button of a multi channel remote control transmitter (Smart Code or Dip Switch Code) or an entry
keypad, to operate the Auxilliary Output feature of this garage door opener. When the programmed remote control
transmitter is operated it will cause the connections on the J8 Connector to close momentarily.

4.12  Vacation Mode

The radio receiver of the garage door opener can be turned off using a remote control transmitter to activate the
Vacation Mode facility. Whilst in vacation mode the opener will not respond to any remote control transmitters.

To activate the Vacation Mode facility, with the garage door in the closed position, press the coded remote control
transmitter. The Power LED will flash slowly to indicate that the opener is in “Vacation Mode”.

Vacation Mode can only be activated when the garage door is in the closed position.

To exit Vacation Mode press the Operate Button on the light cover of the garage door opener.

You may program one “Smart Code”, one “Dip Switch Code” or one “Keypad Code” to operate this feature. It is
recommended that a “Smart Code” remote control transmitter be used as the wall button – program one button to
control the “Vacation Mode” feature. This will reduce the possibility of accidental activation of this feature.

4.13  Door Open Indicator

This garage door opener has a Door Open Indicator. When the garage door opener is at the bottom limit, the
terminals 3 and 4 of the J8 connector will become active to provide an indication of the status of the door. For
example, this can be wired into home automation or alarm systems.

20

©Copyright 2003

Part No 059778

Summary of Contents for Controll-A-Door R





























Reviews:

No comments

Brands by name

Popular brands

Load more brands