Balluff BMD 1H Series, User Manual

Page: 100 / 474

18 ÏÏÏƖº¹ÄÄÍŰƖ»ÇÅ
5 Connecting to power supply
54455-EN-170712
5 Connecting to power supply
5.1 Preparing the connection
Always keep in mind the following safety instructions:
Warning:
Connect only in the complete absence of line voltage.
•
The electrical connection must only be carried out by trained
personnel authorised by the plant operator.
•
If overvoltage surges are expected, overvoltage arresters should
be installed.
Power supply and current signal are carried on the same two-wire
»¹ºÄ½ƖÀ½ÇȽʹÌÁÆ¿ÎÇÄ̹¿½»¹Æ¼ÁŰ½Ê¼½È½Æ¼ÁÆ¿ÇÆÌÀ½ÁÆËÌÊÍŽÆÌ
version.
À½¼¹Ì¹¾ÇÊÈÇϽÊËÍÈÈÄѹʽËȽ»ÁŲ½¼ÁÆ»À¹È̽Êͷ Technical data ".
½½ÈÁÆÅÁƼÌÀ½¾ÇÄÄÇÏÁÆ¿¹¼¼ÁÌÁÇƹľ¹»ÌÇÊËÌÀ¹ÌÁÆŴͽƻ½ÌÀ½ÇÈ½Ê¹Ì -
ing voltage:
•
Lower output voltage of the power supply unit under nominal load
(e.g. with a sensor current of 20.5 mA or 22 mA in case of fault)
•
ÆŴͽƻ½Ç¾¹¼¼ÁÌÁÇƹÄÁÆËÌÊÍŽÆÌËÁÆÌÀ½»ÁÊ»ÍÁÌƼ˽½Äǹ¼Î¹ÄͽËÁÆ
chapter " Technical data ")
The instrument is connected with standard two-wire cable without
screen. If electromagnetic interference is expected which is above the
test values of EN 61326-1 for industrial areas, screened cable should
be used.
Make sure that the cable used has the required temperature resist-
¹Æ»½¹Æ¼Ųʽ˹¾½ÌѾÇÊŹÐƖÇ»»ÍÊÊÁÆ¿¹ÅºÁ½ÆÌ̽ÅȽʹÌÍʽ
We generally recommend the use of screened cable for HART
multidrop mode.
Use cable with round cross section for instruments with housing and
cable gland. Use a cable gland suitable for the cable diameter to
½ÆËÍʽÌÀ½Ë½¹Ä½Ű½»ÌǾÌÀ½»¹ºÄ½¿Ä¹Æ¼ƼÈÊÇ̽»ÌÁÇÆʹÌÁÆ¿ƽƖ
Metric threads
In the case of instrument housings with metric thread, the cable
glands are screwed in at the factory. They are sealed with plastic
plugs as transport protection.
You have to remove these plugs before electrical connection.
NPT thread
In the case of instrument housings with self-sealing NPT threads, it is
not possible to have the cable entries screwed in at the factory. The
free openings for the cable glands are therefore covered with red dust
protection caps as transport protection.
Prior to setup you have to replace these protective caps with ap-
proved cable glands or close the openings with suitable blind plugs.
Max. torque for all housings, see chapter "
Technical data ".
Safety instructions
Voltage supply
Connection cable
Cable glands