manualshive.com logo in svg

Bailey INFI 90 IMASO01, Instruction

Share
Download
Bailey INFI 90 IMASO01 Instruction Download Page 7

I-E96-303A   

vii

Sommaire de Sécurité

AVERTISSEMENT

D'ORDRE

GENERAL

Environment de l'equipement
Nes pas soumettre les composantes a une atmosphere corrosive
lors du transport, de l'entreposage ou de l'utilisation.

Risques de chocs electriques lor de l'entretien
S'assurer de debrancher l'alimentation ou de prende les precau-
tions necessaires a eviter tout contact avec des composants sours
tension lors de l'entretien.

Precautions de Manutention
Ce module contient des composantes sensibles aux decharges
electro-statiques.

AVERTISSEMENT

D'ORDRE

SPECIFIQUE

Couper l'alimentation avant d'installer les dipshunts sur la plaque
arriere du chassis de montage de modules (MMU). Toute negli-
gence a cet egard constitue un risque de choc pouvant entrainer
des blessures graves, voire moretiles. (p. 3-5, 5-3)

Les signaux de sortie prennent automatiquement la valeur de 0%
au moment demarrage. Quand une erreur est decelee, ces signaux
prennent une valeur fixe. Cette valeur doit etre affectee par l'utili-
sateur (et configuree dans le MFP), de sorte a assurer un fonction-
nement sur en cas d'erreur. (p. 3-2)

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for INFI 90 IMASO01












































Reviews:

No comments

Brands by name

Popular brands

Load more brands