manualshive.com logo in svg

Bailey INFI 90 IMASO01, Instruction

Share
Download
Bailey INFI 90 IMASO01 Instruction Download Page 23

INSTALLATION

SETUP/PHYSICAL INSTALLATION

3 - 2

  

I-E96-303A

®

SETUP/PHYSICAL INSTALLATION

You must set the address dipswitch (S1) and the analog output
mode switches (S2 through S15)

 BEFORE

 installing or operat-

ing the ASO module. Its respective Termination Unit (TU) or
Termination Module (TM) must be configured to output the
analog signals from the ASO to the field devices.

Slave Address Selection Switch (S1)

The ASO can have one of 64 addresses (address 0 to 63) on the
slave expander bus. This address uniquely identifies the slave
to the master module and must be the same as the address set
in the master module configuration (Function Code (FC) 149
specification 1).

The address is set by the eight position address dipswitch (S1)
shown in Figure 

3-1

. The six right switch positions (3 through

8) of S1 set the six bit ASO address. Positions 1 and 2 are not
used and must remain in the closed position (see Figure 

3-2

).

Table 

3-1

 is a binary address conversion table for setting S1.

WARNING

The outputs go to 0% at start-up. On error detection, these out-
puts will change to a fixed value. This value must be selected
by the user (and configured in the MFP) to ensure safe opera-
tion when error conditions occur.

AVERTISSEMENT

Les signaux de sortie prennent automatiquement la valeur de
0% au moment demarrage. Quand une erreur est decelee, ces
signaux prennent une valeur fixe. Cette valeur doit etre
affectee par l'utilisateur (et configuree dans le MFP), de sorte a
assurer un fonctionnement sur en cas d'erreur.

Figure 3-1.  Analog Slave Output Module

MODULE STATUS LED

ADDRESS SWITCH

TP27147A

1

3

OPEN

S12

1

3

OPEN

S8

1

8

OPEN

S1

1

3

OPEN

S15

1

3

OPEN

S2

1

3

OPEN

S3

1

3

OPEN

S4

1

3

OPEN

S5

1

3

OPEN

S6

1

3

OPEN

S7

1

3

OPEN

S13

1

3

OPEN

S9

1

3

OPEN

S14

1

3

OPEN

S10

1

3

OPEN

S11

P1

P3

P2

EDGE

CONNECTORS

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for INFI 90 IMASO01












































Reviews:

No comments

Brands by name

Popular brands

Load more brands