manualshive.com logo in svg

Bailey INFI 90 IMASO01, Instruction

Share
Download
Bailey INFI 90 IMASO01 Instruction Download Page 14

INTRODUCTION

GLOSSARY OF TERMS AND ABBREVIATIONS (continued)

1 - 4

  

I-E96-303A

®

GLOSSARY OF TERMS AND ABBREVIATIONS 

(continued)

NOMENCLATURE

The following modules and equipment can be used with an
ASO:

Term

Definition

LSB

Least Significant Bit; the bit of a binary number that carries the least numeri-
cal weight.

Master Module

One of a series of controller modules designed to direct field processes 
through a slave module. The multi-function processor is an example.

MFP

Multi-Function Processor Module; a multiple loop controller with data acqui-
sition and information processing capabilities.

MMU

Module Mounting Unit; a card cage that provides electrical and communica-
tion support for INFI 90 modules.

MSB

Most Significant Bit; the bit of a binary number that carries the most numeri-
cal weight.

OIS

Operator Interface Station; integrated operator console with data acquisition 
and reporting capabilities. It provides a window into the process for flexible 
control and monitoring.

PAL

Programmable Array Logic; an integrated circuit that performs logic func-
tions based on a program that is downloaded to it.

PCU

Process Control Unit; rack type industrial cabinet that contains master, slave 
and communication modules, and their communication paths.

RAM

Random Access Memory; processor memory that has both read and write 
capability. This memory is volatile; its contents are lost when power is 
removed.

Slave Expander 
Bus

Parallel address/data bus between the master module and the slave that 
point data and slave status data are exchanged over.

TM

Termination Module; provides input/output connection between plant equip-
ment and the INFI 90 process modules. The termination module slides into a 
slot in the termination mounting unit.

TU

Termination Unit; provides input/output connection between plant equipment 
and the INFI 90 process modules. The termination unit is a flat circuit board 
for panel mounting.

Nomenclature

Hardware

IMMFP01/02

Multi-Function Processor Module

NTDI01

Termination Unit

NIDI01

Termination Module

NKTU01

Cable, Termination Unit

NKTU02

Cable, Termination Module

NKTM01

Cable, Termination Module

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for INFI 90 IMASO01












































Reviews:

No comments

Brands by name

Popular brands

Load more brands