manualshive.com logo in svg

Bailey INFI 90 IMASO01, Instruction

Share
Download
Bailey INFI 90 IMASO01 Instruction Download Page 27

INSTALLATION

FUSING

3 - 6

  

I-E96-303A

®

Wiring

Installing the module in the MMU connects the slave module to
logic power (+5 VDC, 

±

15 VDC), necessary to drive the cir-

cuitry, at P1. It also connects P2 to the slave expander bus for
communication with the MFP. P1 and P2 connection require no
additional wiring or cabling.

NOTE: You must install a dipshunt on the backplane of the MMU to
connect the slave expander bus between the slave module and
master module. Locate the modules so the bus can connect the
modules or they will not communicate.

Cable Connections

The IMASO01 uses either an NTDI01 or NIDI01 for termina-
tion. See Figure 

3-3

 to determine the cables to use with the

TU/TM you are using.

FUSING

The ASO does not have any on board fusing requirements.

PRE-OPERATING ADJUSTMENTS

You do not have to make any adjustments to the ASO prior to
operating.

Figure 3-3.  IMASM01 Cable Connections and Termination

TP27148A

P1

P1

P3

P1

P3

P1

P2

P2

NKTM01

OR

NKTU02

NIDI01

IMASO01

NTDI01

IMASO01

NKTU01

14 ANALOG OUTPUTS
(1-5 VDC, 4-20 mA)

14 ANALOG OUTPUTS
(1-5 VDC, 4-20 mA)

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for INFI 90 IMASO01












































Reviews:

No comments

Brands by name

Popular brands

Load more brands