manualshive.com logo in svg

Bailey INFI 90 IMASO01, Instruction

Share
Download
Bailey INFI 90 IMASO01 Instruction Download Page 4

I-E96-303A1  

31 March 1993

Preface

The Analog Slave Output module (IMASO01) outputs fourteen
analog signals from the INFI 90 Process Management System
to process field devices. Master modules use these outputs to
control a process.

This instruction explains the slave module features, specifica-
tions and operation. It details the procedures to follow to set up
and install an Analog Slave Output (ASO) module. It explains
troubleshooting, maintenance and module replacement proce-
dures.

The system engineer or technician using the ASO should read
and understand this instruction before installing and operat-
ing the slave module. In addition, a complete understanding of
the INFI 90 system is beneficial to the user.

This instruction includes updated information that covers
changes to the specification of the ASO module.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for INFI 90 IMASO01












































Reviews:

No comments

Brands by name

Popular brands

Load more brands