manualshive.com logo in svg

Bailey INFI 90 IMASO01, Instruction

Share
Download
Bailey INFI 90 IMASO01 Instruction Download Page 31

TROUBLESHOOTING

ERROR INDICATIONS AND CORRECTIVE ACTION

5 - 2

  

I-E96-303A

®

The address set on address switch (S1) and in the MFP config-
uration must be the same. The MFP generates a MISSING
SLAVE MODULE error if they do not match. Verify that the
address set on S1 is the same as the address in FC 149 specifi-
cation 1. If not:

1. Remove the module and change the setting of S1 to corre-
spond with the MFP configuration (refer to 

Section 3

 for the

procedures to set an address and to install a slave module).

OR

2. Modify the address in the MFP configuration (FC 149 speci-
fication 1) to correspond with the address set on S1. Use an Infi
90 operator interface to modify the configuration (for proce-
dures on how to modify a function code specification, refer to
the Product Instruction for the operator interface you are
using).

Table 5-1.  Status LED Indications and Corrective Actions

LED State

Indication

Probable Cause

Corrective Action

Solid Green

Slave module operating 
normally and communi-
cating with master mod-
ule

Normal operation

No action required

Off

Slave module not 
enabled

Address set on S1 not the 
same as address in master 
module configuration FC 149 
spec 1

Change address on S1 to corre-
spond with FC 149 spec 1

OR

Change address in FC 149 spec 
1 to correspond with S1

Dipshunt not properly installed 
between master module and 
slave module

Verify dipshunt is installed prop-
erly (no bent pins) in slave 
expander bus socket on MMU 
backplane between master and 
slave module

Master module configuration 
is not correct

Verify FC 149 is in master mod-
ule configuration

No power to slave mod-
ule

Module not completely 
inserted in MMU

Verify module is completely 
inserted in MMU: faceplate flush 
with MMU and captive retaining 
screws latched

Red

Bus fault timer error 
(

time-out)

Slave expander bus clock fail-
ure

Check master module for proper 
operation

Dipshunt not installed 
between master and slave 
module

Verify dipshunt is installed in the 
slave expander bus socket on the 
MMU backplane between master 
and slave module

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for INFI 90 IMASO01












































Reviews:

No comments

Brands by name

Popular brands

Load more brands