manualshive.com logo in svg

Bailey INFI 90 IMASO01, Instruction

Share
Download
Bailey INFI 90 IMASO01 Instruction Download Page 15

INTRODUCTION

SPECIFICATIONS

I-E96-303A   

1 - 5

SPECIFICATIONS

REFERENCE DOCUMENTS

Power Requirements

Voltage

Current Consumption

Power Dissipation

+5 VDC

 ±

5%

+15 VDC

 ±

5%

-15 VDC 

±

5%

+24 VDC 

±

10% (from termination unit/termination module)

480 mA (+5 VDC)
200 mA (+15 VDC)
195 mA (-15 VDC)
310 mA (+24 VDC)

3.75 watts @ +5 VDC
5.25 watts @ +15 VDC
3.75 watts @ -15 VDC

D/A Resolution

10 bits for analog outputs

Output Accuracy

≤

0.15% (voltage mode)

≤

0.25% (current mode)

Output Load

750 ohms maximum (current mode)
22 kilohms minimum (voltage mode)

Current Limiting

Short Circuit Protection

50 mA (nominal) output current limit

Surge Protection

Meets IEEE-472-1974 Surge Withstand Capability Test

1

Mounting

Occupies one slot in standard INFI 90 Module Mounting Unit.

Environmental

Ambient Temperature

Relative Humidity

Altitude

Air Quality

0

o

 to 70

o

 C (32

o

 to 158

o

 F)

0% to 95% up to 55

o

 C (131

o

 F)(non-condensing)

0% to 45% at 70

o

 C (158

o

 F)(non-condensing)

Sea Level to 3 Km (1.86 miles)

Non-corrosive

Certification

CSA certified for use as process control equipment in an ordinary 
(non-hazardous) location.

NOTE: 1. Do not use the NKTM01 cable when compliance with IEEE-472-1974 is necessary.

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

Document  

Number

Description

I-E92-501-2

Configuration and Tuning Terminal

I-E93-916

Engineering Work Station

I-E96-100

Operator Interface Station

I-E96-200

Function Code Application Manual

I-E96-201

Multi-Function Processor (IMMFP01)

I-E96-202

Multi-Function Processor (IMMFP02)

I-E96-410

Digital I/O Termination Module (NIDI01)

I-E96-424

Digital I/O Termination Module (NTDI01)

I-E96-303A1

31 March 1993

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for INFI 90 IMASO01












































Reviews:

No comments

Brands by name

Popular brands

Load more brands