INSTALLATION
SETUP/INSTALLATION
I-E96-301B
3 - 3
through 8) of SW1 set the six bit address. Positions 1 and 2
must remain closed (set to zero) for normal operation.
Table
lists the binary addresses for setting SW1. Refer to
for the diagnostic settings for SW1.
Configuring Inputs
Configure the IMASI03 by setting the specifications in function
code 215 and 216 in the master MFP and setting the input
jumpers on both the IMASI03 slave and the termination device.
Refer to
for more information on configuration and
calibration. Refer to
for more information on func-
tion code 215 and 216.
Each Input on the IMASI03 has two jumpers. Set both jumpers
on each input to pins 2 and 3 for a resistance (3-wire RTD)
Table 3-1. Address Switch Settings (S1)
MSB
LSB
MSB
LSB
Addr
3
4
5
6
7
8
Addr
3
4
5
6
7
8
0
1
2
3
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
32
33
34
35
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
4
5
6
7
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
0
1
1
0
1
0
1
36
37
38
39
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
0
0
1
1
0
1
0
1
8
9
10
11
0
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
0
1
1
0
1
0
1
40
41
42
43
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
0
0
1
1
0
1
0
1
12
13
14
15
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
1
1
0
1
0
1
44
45
46
47
1
1
1
1
0
0
0
0
1
1
1
1
1
1
1
1
0
0
1
1
0
1
0
1
16
17
18
19
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
48
49
50
51
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
20
21
22
23
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
1
0
1
52
53
54
55
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
1
0
1
24
25
26
27
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
1
1
0
1
0
1
56
57
58
59
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
1
1
0
1
0
1
28
29
30
31
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
0
0
1
1
0
1
0
1
60
61
62
63
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
1
1
0
1
0
1
