Bacci MASTER Use And Maintenance Instruction Manual Download Page 165

Page: 165 / 238

MASTER

–

Instruction manual

Chap. 5
-

/62 -

CONSTRUCTION NOTE

Construction

information

INFORMATION!

When projecting the creation of templates, take into account the following
considerations:

Provide for at least 2 anchoring points at the extremities.

Provide for at least 2 blocking presses for the piece.

Provide for at least 2 perpendicular stopping guides for the piece.

5.11.6

Checking for correct piece blocking

Templates are not supplied with the machine.
The example below serves only for information purposes.

NOTE

Safety

warning

DANGER!

Danger of flying pieces or tool parts.

Inadequate blocking with respect to machining force may result in:

Piece flying free

Tool breaking and consequently flying free.

Make sure that the piece has been blocked properly before starting the work cycle.

After having assembled and adjusted the blocking devices, including templates, carefully check that the
piece has been properly blocked. Make sure the piece is held fast in all directions in which machining
force will be applied.

Summary of Contents for MASTER















































































































































































































































Search results

Summary of Contents for MASTER

Reviews:

Related manuals for MASTER

Brands by name

Popular brands

Bacci MASTER, Use And Maintenance Instruction Manual

Search results

Summary of Contents for MASTER

Reviews:

Related manuals for MASTER

Brands by name

Popular brands