Bacci MASTER Use And Maintenance Instruction Manual Download Page 159

Page: 159 / 238

MASTER

–

Instruction manual

Chap. 5
-

/62 -

5.9.6

Cleaning machine tools

The tools, tool holder and any spacers used must be dynamically balanced in G1.

MAINTENANCE NOTE

Machine

maintenance

information

INFORMATION!

The components listed below must be kept absolutely clean:

Cones

Shafts

Tool gripping pincers

DANGER!

Danger of tool holder group breakage.

The presence of dust deposits on the tool stem may cause:

Tool misalignment

Ineffective tool blocking.

If the operator tightens the pincer-holder ring nut with excessive tightening torque,
the shaft or tool-holder threading may be damaged.

Clean tools thoroughly.

Do not tighten the ring nut with torque greater that the recommended torque.

RECOMMENDED TIGHTENING TORQUE:

Summary of Contents for MASTER















































































































































































































































Search results

Summary of Contents for MASTER

Reviews:

Related manuals for MASTER

Brands by name

Popular brands

Bacci MASTER, Use And Maintenance Instruction Manual

Search results

Summary of Contents for MASTER

Reviews:

Related manuals for MASTER

Brands by name

Popular brands