B2 HVA Series User Manual Download Page 97

Page: 97 / 106

Disconnection Procedure

DHV0086 Rev06

Steps D1-D7 describe the normal disconnection procedure.

Step Procedure

Press emergency off

Stop test according to

see 5.4 Interrupting a Test on page 73

and press emergency off button

to lock against re-energise.

Verify HV status. Wait until red LED

light deactivates.

(Red light indicates residual voltage > 100V)

Discharge and earth the DUT complying with local safety regulations .

Lock HVA in disabled state to prevent unauthorized use:

• Turn key switch

to the OFF position.

Disconnect the Test Lead

• Disconnect test lead from DUT

• Disconnect

earth cable from the HV cable shield

• Unscrew HV test lead from HVA HV output connector

• Disconnect power supply cable from power supply plug

Disconnect all earthing cables

• Disconnect earthing cable from DUT earth

• Disconnect earthing cable form HVA earthing connector

Summary of Contents for HVA Series











































































































Search results

Summary of Contents for HVA Series

Reviews:

Related manuals for HVA Series

Brands by name

Popular brands

B2 HVA Series, User Manual

Search results

Summary of Contents for HVA Series

Reviews:

Related manuals for HVA Series

Brands by name

Popular brands