manualshive.com logo in svg

Axminster Trade AT254PS13, Manual

Share
Download
Axminster Trade AT254PS13 Manual Download Page 36

Changing the Saw Blade

36

7. Replace the kerf plate and inner guard assembly. Slide 
the table back until the locking knob pin engages the pin 
recess. Turn the saw blade once by hand to check it spins 
freely and replace the crown guard. When everything is 

satisfactory, reconnect the machine to the mains supply.
Give the machine a test run ( i.e. quick ON-OFF) to 
ensure everything is OK. If everything is satisfactory,  
continue to use the panel saw. 

Routine Maintenance

•  Keep the saw as clean and free from saw dust build up 

as practical.

•  Periodically, unlock the sliding table and push to one 

side and remove the inner guard to gain access to 
the saw mechanism. Raise the saw blade to it’s high-
est point, remove the crown guard and blow, brush or 
vacuum out the saw inner workings, using a proprietary 
resin cleaner.

•  Check the saw blade regularly for chipped ,missing, 

damaged teeth etc. and remove any resin build up from 
the blade/s, riving knife etc. 

•  After several months of constant use the condition of 

the chains, sprockets, tension of the drive belts and the 
threaded drive shafts of the rise and fall tilt mechanisms 
will need to be checked; that may require a service 
engineer to oversee the job.

 •   If you find that the machine is not performing as 

it should please contact our “Specialist After Sales 
Team” by phone on 03332 406 406 or visit our 
website at axminster.co.uk.

•  If the “Panel Saw” is not going to be used for a period 

of time, spray a light coat of oil over the table surface 
and blades that will help prevent rust.

General Information

Sliding Table (Side Play Movement)

After several months of use, if you notice the sliding 
table shows signs of ‘slide play’ movement follow the 
instruction below.

WARNING!! DISCONNECT THE MACHINE 
FROM THE MAINS BEFORE CONTINUING!

1. Pull the sliding table locking knob towards you and 
slide the table to the side exposing the cap head screws 
beneath, see 128.

2. Adjust each screw in turn, (one rotation) should be 
sufficient. Slide the table to the opposite end and repeat 
the procedure. Check the table to see that the slide play 
has been queried. If OK, re-lock the table. 

Fig 128

Cap head screw

WARNING!! DISCONNECT THE MACHINE 
FROM THE MAINS BEFORE CONTINUING!

Inspecting and Changing the Drive Belts

Check the blade drive belts for any signs of wear 
including fraying, stretching, missing teeth and basic 
wear and tear etc. Follow the instructions below.  

1. Slide the table to one side and remove the crown 
guard and inner guard, place safely aside.

2. Remove the main blade, as instructed on page 35.

3. Remove the fixing that secures the extractor housing 
assembly, see figs 129 place them safely aside and lower 
housing assembly down to the floor.

Main Saw Blade

Fig 129

Cap head bolt

Summary of Contents for AT254PS13





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands