manualshive.com logo in svg

Axminster Trade AT254PS13, Manual

Share
Download
Axminster Trade AT254PS13 Manual Download Page 13

Assembly

13

curved slot in the riving knife. Tighten the clamping 
knob, see fig 33-34.

Fig 3-34

Curved slot

13

12

Clamping knob

17. Place a 50mm hose clip (21) over the end of the hose 
(19), see fig 35. Insert the hose over the extraction outlet 
on the crown guard (13) and tighten the clip, see fig 36.

NOTE: DO NOT OVER TIGHT AS THE CROWN GUARD IS 
PLASTIC AND LIABLE TO  BREAK!

Fig 35-36

21

19

Extraction outlet

18. Place the remaining clip over the opposite end of the 
hose. Insert the hose over the 50mm inlet on the 100mm 
extraction moulding (17) and tighten the clip, see fig 37.

Fig 37

19. Locate the hose support bracket (22). Remove the 
bolt/washer and nut, line up the hole in the bracket with 
the mounting hole to the end of the side extension table 
(4) and secure with the fixings you just removed, see fig 
38. Slot the hose (19) onto the bracket, see fig 39.

Fig 38-39

22

19

4

20. Replace the inner guard assembly.

Continues Over....

Summary of Contents for AT254PS13





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands