manualshive.com logo in svg

Axminster Trade AT254PS13, Manual

Share
Download
Axminster Trade AT254PS13 Manual Download Page 12

Assembly

12

M8x20mm bolts/washers

Straight edge

14. Locate the crown guard assembly (13), riving knife 
(12), 50mm flexible hose (19), the two 50mm hose clips 
(21) and the hose support bracket (22).  Remove the two 
Phillips screws holding the inner guard assembly and 
place safely aside, see 27-28.

Crown Guard 

Fig 27-28

15. Loosen the two bolts holding the mounting plates. 
Lower the riving knife (12) down between the mounting 
plates, set the riving knife close to the blade and check 
the clearance between the blade. It should have a gap of 
(MIN 3mm - MAX 8mm), tighten the two bolts to secure 
the setting, see fig 29-30-31-32.

Fig 29-30-31-32

12

Mounting plate

Rear mounting plate

3-8mm Gap

between the

riving knife

and the blade

Clearance

Inner guard

Phillips screw

16. Locate the crown guard assembly (13) and loosen 
the clamping knob. Introduce the slot to the rear of the 
guard over the riving knife and slot the pin bolt into the 

Summary of Contents for AT254PS13





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands