manualshive.com logo in svg

Axminster Trade AT254PS13, Manual

Share
Download
Axminster Trade AT254PS13 Manual Download Page 28

Positioning the Machine

28

Setting Up the Machine

Ascertain the orientation of the machine and move it 
to its desired position in the workshop. Ensure that the 
machine is positioned to allow sufficient clearance all  
round to cater for the maximum length of timber you 

wish to machine. The machine should be positioned on 
a flat level surface.  Manoeuvre the machine to the 
chosen location, then carefully lower the machine down.

WARNING!! DISCONNECT THE MACHINE 
FROM THE MAINS BEFORE CONTINUING!

Setting the Saw Blade at 90˚

1. Remove the crown guard and place to one side, raise 
the saw to it’s maximum height by turning the operating 
wheel counterclockwise. Place a 90˚ square up against 
the saw blade and check the blade is 90˚ to the table, see 
fig 91. 

Fig 91

90˚ Square

2. If the blade needs adjustment loosen the grub screws
on the 90˚stop collar on the saw assembly, see fig 92 and 
adjust the collar in small increments until the bade is 
perpendicular with the table. Nip up the collar to lock
 the setting. Reset the scale pointer if required.

Fig 92

Setting the Saw Blade at 45˚

3. Set the angle of the saw to 45˚, place a mitre square 
up against the blade and check it is 45˚ with the table. 
If adjustment is required loosen the grub screws on the 
45˚stop collar on the saw assembly, see fig 93. Adjust 
the collar in small increments until the bade is 
perpendicular with the table. Nip up the collar to lock 
the setting.

Fig 93

45˚ Mitre square

Extension Table Fence

1. Raise the blade to its maximum height, slacken the 
butterfly knob (A) and the steel pin by loosening the 
clamping knob (B). Slide the fence up close to the saw 

blade, make sure the extension fence is up against the 
90˚ fence stop, see fig 94. Using a 90˚ square, place it 
against the fence and the blade (not on the teeth), see fig 
95. Check that the angle is correct, if not adjust the 90˚ 
adjusting nut until the fence is square to the blade, see 
fig 96.

A

B

Fig 94-96

90˚ Fence stop

Summary of Contents for AT254PS13





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands