manualshive.com logo in svg

Axminster Trade AT254PS13, Manual

Share
Download
Axminster Trade AT254PS13 Manual Download Page 34

A

Operating Instructions

WARNING!! DISCONNECT THE MACHINE 
FROM THE MAINS BEFORE CONTINUING!

DISCONNECT THE MACHINE FROM THE 
MAINS!

WARNING!!  IT IS IMPORTANT THE FRONT 
EDGE OF THE FENCE NEVER PASSES THE 
CENTRE OF THE BLADE.

Rip Saw Cutting

1. Set the crown guard 3-4mm above the  top of the 
workpiece, see fig 118.

2. Set the fence for the width of cut.

A push stick must be used when making cuts less than 
300mm in length.  The push stick should be at least 
450mm long with a ‘bird’s mouth to one end, see 
illustration below.

RECONNECT THE MACHINE TO THE MAINS!

Bird’s mouth

Start the saw by pressing the ‘ON’ button on the NVR
switch. Wait until the saw is at full speed, if everything 
sounds and feels OK, carefully guide a test workpiece 
safely through, checking there is no build up of dust.

If all is OK.,turn off the saw, wait until the saw comes
to a complete stop before removing the workpiece. 

RECONNECT THE MACHINE TO THE MAINS!

3. Start the saw, wait until it’s at full speed and carefully 
feed the workpiece through using a ‘push stick’.  Make 
sure the workpiece is clear of the blade then turn off the 
saw, wait until the saw comes to a complete stop before 
removing the workpiece. 

Bevel Cut

There is an angle scale mounted on top of the extension 
table, to set the fence at required angles for cutting
bevel cuts, see fig 121.

Fig 121

Angled scale

34

HSE Health and Safety Executive

To operate the ‘Panel Saw’ correctly, it is 
recommended to visit the HSE (Health and 
Safety Executive) website at www.hse.gov.uk 
and read the information on the safe practices.

Summary of Contents for AT254PS13





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands