AXIOMTEK IPC960-525 Series User Manual Download Page 68

Page: 68 / 124

IPC960/IPC962/IPC964-525 Series U

ser’s Manual

Hardware Installation

2.7.3 The length limitation of an add-on card

The following figures show the length limitation of an add-in card.

IPC962

IPC964

System configuration: w/o add-on card power cable & w/o internal fan module

Note: Please note that 234mm is the maximum length for add-on card with I/O bracket.

Considering heat dissipation potential, a space of 30mm must be left between
add-on card and system.

IPC962

IPC964

System configuration: w/ add-on card power cable

Note: When using the power connector on riser card, it is strongly recommended that

add-on cards

’

length cannot exceed 185mm.

Summary of Contents for IPC960-525 Series





























































































































Search results

Summary of Contents for IPC960-525 Series

Reviews:

Related manuals for IPC960-525 Series

Brands by name

Popular brands

AXIOMTEK IPC960-525 Series, User Manual

Search results

Summary of Contents for IPC960-525 Series

Reviews:

Related manuals for IPC960-525 Series

Brands by name

Popular brands