manualshive.com logo in svg

Avidyne IFD540, Installation Manual

Share
Download
Avidyne IFD540 Installation Manual Download Page 78

 

IFD5XX Installation Manual 

600-00299-000 

Page 78 of 198 

Revision: 02 

7.4  Unit Installation  

Install unit in the tray using the captive 3/32” Hex screw. Verify the connectors are fully 
engaged prior to powering on the unit. 

7.5  Configuration 

The IFD5XX can be configured in the aircraft. This section will describe the procedures for 
configuring the IFD5XX. 

Configuration consists of setting up communication protocols in Maintenance Mode, 
designating specific types of equipment to be integrated and setting up system settings. 

Configuration also consists of setting up User Options preferences in non-Maintenance Mode 
via the SYS tab of the AUX page. 

For new installations, use this section to configure the IFD5XX for the specific airplane. 

For replacement installations in which the IFD5XX is replacing a GNS 530/W, use Appendix 
F: Configuration Setup of this manual to first record the configuration of the GNS530/W that 
is being replaced by the IFD5XX and then using that recorded data, use the IFD5XX 
Maintenance Mode pages as defined in this section and Appendix F: Configuration Setup to 
properly set up and record configurations. 

7.5.1  Maintenance Mode 

The Maintenance Mode can be accessed by using the following procedures (on the ground 
only): 

1.

 

Power on the IFD5XX  

2.

 

Press Enter Button to accept the on screen statement 

3.

 

Press Proceed Line Select Key (LSK) followed by the Confirm LSK on the database 
acknowledgement screen (if shown) 

4.

 

Select the “AUX” function key to display the Auxiliary Page. Press on the right side 
of the “AUX” Function key until the “SYS” tab is shown 

5.

 

Select “Update Databases” LSK by pressing the associated button.  Press the 
“Confirm” LSK after it appears.  The screen will blank for several seconds before 
coming up in Maintenance Mode 

Summary of Contents for IFD540







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands