manualshive.com logo in svg

Avidyne IFD540, Installation Manual

Share
Download
Avidyne IFD540 Installation Manual Download Page 141

 

IFD5XX Installation Manual 

600-00299-000 

Page 141 of 198 

Revision: 02 

NOTES:

    1.    ALL WIRES TO BE 24 AWG OR GREATER UNLESS OTHERWISE NOTED.

    2.

AT IFD540 UNIT, TERMINATE SHIELD GROUNDS TO THE CONNECTOR BACKSHELL OR USE 
CARD-EDGE CONNECTOR TO TERMINATE SHIELD GROUNDS TO BACK PLATE. THE SHIELD LEADS 
MUST BE LESS THAN 3.0 INCHES. CONNECT OTHER SHIELD GROUNDS TO AIRCRAFT CHASSIS 
WITH AS SHORT A CONDUCTOR AS PRACTICAL.

    3.

IF THE GPS ARINC 429 IN 1 PORT (P1001-48 AND -49) IS ALREADY USED FOR ANOTHER PURPOSE, 
THE GPS ARINC 429 IN 2 PORT (P1001-50 AND -51) MAY BE CONNECTED INSTEAD.

    4.

REFER TO SECTION 7 FOR ARINC 429 CHANNEL SETTINGS.

    5.

REFER TO SECTION 7 FOR RS-232 CHANNEL SETTINGS.

    6.

REFER TO MANUFACTURER’S DOCUMENTATION FOR COMPELTE PINOUT AND INTERCONNECT 
INFORMATION. PINOUTS OF OTHER UNITS SHOWN FOR REFERENCE ONLY.

    

3

 

 

Page 2 of 2  

Summary of Contents for IFD540







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands