manualshive.com logo in svg

Avidyne IFD540, Installation Manual

Share
Download
Avidyne IFD540 Installation Manual Download Page 135

 

IFD5XX Installation Manual 

600-00299-000 

Page 135 of 198 

Revision: 02 

NOTES:

    1.    ALL WIRES TO BE 24 AWG OR GREATER UNLESS OTHERWISE NOTED.

    2.

AT IFD540 UNIT, TERMINATE SHIELD GROUNDS TO THE CONNECTOR BACKSHELL 
OR USE CARD-EDGE CONNECTOR TO TERMINATE SHIELD GROUNDS TO BACK 
PLATE.

    3.

REFER TO SECTION 7 FOR RS-232 CHANNEL SETTINGS

    4.

REFER TO THE GTX 327 TRANSPONDER INSTALLATION MANUAL, 190-00187-02, 
FOR COMPLETE INFORMATION.

    5.

IF TWO OR MORE IFD4XX/5XX SERIES UNITS ARE INSTALLED, THE RS-232 LINE 
ON P1001-41 AND P1001-42 MAY BE CROSS-CONNECTED TO CROSSFILL FLIGHT 
PLANS AND USER WAYPOINTS. TO CROSSFILL FLIGHT PLANS, IT IS REQUIRED 
THAT BOTH UNITS HAVE IDENTICAL DATABASE CYCLE DATES AND MAY BE 
REQUIRED THAT THEY HAVE IDENTICAL VERSIONS OF THE MAIN SOFTWARE. 
REFERENCE SECTION 4 FOR WIRING INFORMATION.

    6.  

MAPMX (MAIN SOFTWARE VERSION 3.10 AND LATER) IS THE PREFERRED 
COMMUNICATION PROTOCOL FOR THE MX20/GMX200. OTHER INPUT PORTS ON 
MX20/GMX200 MAY BE USED INSTEAD OF THE PORT SHOWN. REFER TO 
APPROPRIATE MANUFACTURER’S INSTALLATION DOCUMENTATION.

    7.

REFER TO MANUFACTURER’S DOCUMENTATION FOR COMPLETE PINOUT AND 
INTERCONNECT INFORMATION. PINOUTS OF OTHER UNITS SHOWN FOR 
REFERENCE ONLY.

    8.

IF USING THE SERIAL PORT SOFTWARE METHOD TO CONFIGURE THE OUTPUT 
OF THE ENCODER, 

ENSURE THAT THE “TRIMBLE/GARMIN 9600 BPS” FORMAT IS 

SELECTED.

    9.

MOD LEVEL 8 (OR HIGHER) IS REQUIRED TO SUPPORT RS-232 INTERFACE. 
ENSURE THAT JUMPERS ARE SET FOR “TRIMBLE/GARMIN 9600 BPS” AND “10 
FOOT RESOLUTION.

”

   10      THE IFD5XX STC DOES NOT PROVIDE INSTALLATION APPROVAL OF ANY 

PORTABLE ELECTRONIC DEVICES. ADDITIONAL INSTALLATION APPROVAL IS 
REQUIRED FOR THESE DEVICES.

   

5

8

9

10

 

Page 2 of 2 

Summary of Contents for IFD540







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands