manualshive.com logo in svg

Avidyne IFD540, Installation Manual

Share
Download
Avidyne IFD540 Installation Manual Download Page 109

 

IFD5XX Installation Manual 

600-00299-000 

Page 109 of 198 

Revision: 02 

8.  Flight Checks 

The IFD5XX must be flight tested to verify the installation is operating properly. The 
following items should be tested in flight to verify the IFD5XX function. 

8.1  GPS Flight Test 

Verify the following in flight: 

 

Verify the GPS reception during all phases of flight. (e.g., bank angles of up to 30 
degrees and pitch angles associated with take-off, departures, landing and missed 
approaches) 

 

Verify the following GPS/FMS operation: 

 

Hold at a designated waypoint 

 

Intercept and track to or from a waypoint on a selected course 

 

Waypoint sequencing 

 

Verify the overall operation of procedures or paths  

 

Selection of an approach 

 

Evaluate the display of navigation parameters on the flight instruments (PFD, HSI, 
CDI) is correct 

 

Verify annunciation is correct and in the Pilot's field of view 

8.2  VHF COM Flight Check 

Verify inflight the IFD5XX VHF communication transceiver in the high, mid, and low 
frequency ranges. Test the VHF at least 50 nautical miles and at an appropriate altitude. 

8.3  VOR Flight Checks 

Verify inflight the IFD5XX VHF navigation receiver by tuning a local VOR station within 50 
nautical miles. Verify the audio tone is heard and course deviation information and flag 
information is correct.  

8.4  ILS Flight Test 

Verify inflight the IFD5XX VHF navigation receiver by tuning an airport with an ILS. Verify 
the NAV ID audio tone is heard and the course deviation and flag information is correct. 

8.5  Autopilot 

Verify the IFD5XX interface to the autopilot is correct. Reference the Autopilot Manual 
installation/maintenance manual for test procedures. Verify the following functions: 

 

Evaluate the steering response while in Flight Director (FD) and when the 
autopilot is coupled 

 

Execute several fly-by-turns with varying wind conditions for the FD and 
autopilot 

Summary of Contents for IFD540







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands