manualshive.com logo in svg

Avidyne IFD540, Installation Manual

Share
Download
Avidyne IFD540 Installation Manual Download Page 75

 

IFD5XX Installation Manual 

600-00299-000 

Page 75 of 198 

Revision: 02 

 

6.11.1  Audio 

Pin Name 

Connector 

Pin 

I/O 

Audio 1 HI 

P1001 

37 

Output 

Audio 1 LO 

P1001 

38 

Output 

Audio 2 HI 

P1001 

52 

Output 

Audio 2 LO 

P1001 

53 

Output 

Table 55: Terrain Awareness Audio Output 

The audio output 1 is a low impedance output. 100mW at 500-ohm. 

The audio output 2 has an output impedance of 240-ohm and is capable of driving 100mW 
into a 500-ohm load. 

6.11.2  Annunciators 

Pin Name 

Connector 

Pin 

I/O 

Terrain not available 
annunciate 

P1050 

9 

Output 

Terrain Warning Annunciate 

P1050 

10 

Output 

Terrain Caution Annunciate 

P1050 

11 

Output 

TAWS Inhibit Annunciate 

P1050 

12 

Output 

Table 56:Terrain Awareness Annunicator Output 

6.12  ADS-B/Transponder Output 

The IFD5XX will transmit ADS-B compliant GPS position data to the following compatible 
ADS-B capable transponders 

Manufacturer 

Model 

Notes 

Avidyne 

AXP340 

ADS-B output requires a separate 
installation approval. 

Connect the appropriate input 
pin on the AXP340 with the 
IFD5XX P1001 Pin 8 in order to 
get automatic on-ground / in-air 
mode transition. 

Table 57: ADS-B Output 

Summary of Contents for IFD540







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands