Aviation Design Falcon 7X Assembly Manual Download Page 15 | Manualshive

Page: 15 / 28

background image

AVIATION DESIGN

- ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - [email protected] – www.adjets.com

15

Battery support:

Glue the plywood battery support on the two
wood gear ribs

Glue some small plywood reinforcements (4
pieces, 1 top, 1 bottom, 1 left and 1 right) to
screw the nose on them.

Assembling the wing joining tube:

Check on the front fuselage the location for the 2-wing aluminum joining tube.
Drill 2 X 30 mm hole in the fuselage at the correct location.

Insert the 2 x 30 mm diameter fiber tube in the fuselage
The short tube in the front one, the rear tube is the long one. Mark them (front and rear)
Put some wax on the aluminum tubes.
Fit the aluminum tubes through the fuselage, through the fiber tube, and through the plywood
reinforcements and fit the two wings.

Glue with slow epoxy and microballoon the two fiber tubes and the two plywood reinforcements.
Let it dry overnight.

«
...
13
14
15
16
17
...
»

Summary of Contents for Falcon 7X





























Reviews:

No comments

Related manuals for Falcon 7X

WEEKEND Fokker Dr.I

Brand: Eduard Pages: 12

Brand: Trix Pages: 60

Portable Pit Stop Ramp

Brand: Race Ramps Pages: 6

Brand: GREAT PLANES Pages: 50

Brand: Enabling Devices Pages: 2

Antares C3M4 Combat Drone

Brand: Warlord Games Pages: 2

CHOU CHOU Magic Pacifier

Brand: Zapf Creation Pages: 5

MX Orbital Transport KMX-01

Brand: SEMROC Pages: 4

Wasp Indoor/Outdoor Helicopter 8632

Brand: Excalibur Pages: 1

Brand: Bada namu Pages: 7

Brand: BCP Pages: 12

Brand: TILLIG BAHN Pages: 4

Brand: Trix Pages: 12

Brand: RC4WD Pages: 18

Brand: Jamara Pages: 2

Garden Center 130253

Brand: Faller Pages: 8

Premier 4-8-8-4

Brand: M.T.H. Pages: 29

Brand: Horizon Hobby Pages: 152

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands