Avaya P130 SMON User Manual Download Page 103

Page: 103 / 160

Chapter 6 Avaya P130 CLI

Avaya P130 User’s Guide

Do you want to continue (y/n) [n]? y
VLAN 4 deletion successful

Set inband vlan Command

Use the

set inband vlan

command to set a value for the management vlan (from

1 to 4079).

The syntax for this command is:

set inband vlan

<value>

Example:

P130-1# set inband vlan 1
Management VLAN number set to 1

Show vlan Command

Use the

show vlan

command to display information about VLANs that exist on

the switch.

The syntax for this command is:

show

vlan [<vlan-id> | name <vlan-name>]

Example:

P130-N> show vlan
Vlan-id Vlan-name
------- ---------
1 Vlan1

<value>

A VLAN number between 1 and 4079.

<vlan_id>

Number between 1 and 4079, identifying the VLAN.

<vlan-name>

Name of VLAN

Summary of Contents for P130 SMON

































































































































































Search results

Summary of Contents for P130 SMON

Reviews:

Related manuals for P130 SMON

Brands by name

Popular brands

Avaya P130 SMON, User Manual

Search results

Summary of Contents for P130 SMON

Reviews:

Related manuals for P130 SMON

Brands by name

Popular brands