Avaya P130 SMON User Manual Download Page 29 | Manualshive

Page: 29 / 160

background image

Avaya P130 User’s Guide

15

Chapter 3

Applications

Typical Applications

The Avaya P130 is a low cost workgroup switch that is connected at the edge of the
LAN. It connects end-users and servers and forwards their traffic into the core of the
network.
As shown in the application below, P130 can be connected at the edge of a LAN, or
stacked in a group. The P130 can be connected to the backbone or to the distribution
switch using a LAG or single link connections, that can support LAG or link
redundancy.

Figure 3.1

The Avaya P130 in a Network

Internet

10/100 Mbps Ethernet

10/100 Mbps Ethernet

10/100 Mbps Ethernet

Avaya P882

Avaya WAN Access

Avaya P130

Avaya P130

Avaya P130

4 x 100 Mbps
Ethernet LAG

GBIC Ethernet

with Redundancy

GBIC Ethernet

with LAG and

Redundancy

10/100 Mbps Ethernet

Server Farm

100 Mbps
Fiber
Ethernet

Avaya P332G-ML

Avaya P880

«
...
27
28
29
30
31
...
»

Summary of Contents for P130 SMON

































































































































































Reviews:

No comments

Related manuals for P130 SMON

Brand: Canon Pages: 82

Powershot A650 IS

Brand: Canon Pages: 49

TRANSCEND EM/NT 6.3

Brand: 3Com Pages: 39

DocuColor 45054549

Brand: Xerox Pages: 30

65014293 - Photoshop CS4 - Mac

Brand: Adobe Pages: 87

Brand: Teklynx Pages: 30

Document centre 490

Brand: Xerox Pages: 102

Brand: Brocade Communications Systems Pages: 64

AMD-8151 HyperTransport AGP3.0

Brand: AMD Pages: 16

Brand: Mitsubishi Electric Pages: 92

Brand: Mitsubishi Electric Pages: 51

Brand: Mitsubishi Electric Pages: 57

Brand: Mitsubishi Electric Pages: 29

Network Video Recorder

Brand: ACTi Pages: 132

Brand: Packet8 Pages: 43

Brand: 10ZiG Technology Limited Pages: 125

Brand: AMX Pages: 53

AUTOCAD ELECTRICAL 2005

Brand: Autodesk Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands