Avaya P130 SMON User Manual Download Page 69

Page: 69 / 160

Chapter 6 Avaya P130 CLI

Avaya P130 User’s Guide

Show running-config Command

Use the

show running-config

command to display the currently running

configuration of the module.
This command applies to Policy only.

The syntax for this command is:

show running-config

Example:

P130-N> show running-config
! Avaya P130 Switch-Multilayer Policy configuration
! version 2.9.1
P130-N>

Show startup-config Command

Use the

show startup-config

command to display the startup configuration of

the module.
This command applies to Policy only.

The syntax for this command is:

show startup-config

Example:

P130-N> show startup-config
! Avaya P130 Switch-Multilayer Policy configuration
! version 2.9.1
P130-N> P130-1(super)#

Show stack-config Command

Use the

show stack-config

command to display the stack configuration.

The syntax for this command is:

show stack-config

Example:

P130-N> show stack-config

!#*******************************************************
!# Upload time: 11:11:33 31 JAN 2001 GMT
!# System description:

Avaya Stack of P130 workgroup switches

!# IP address, netmask: 149.49.48.109, 255.255.255.0
!# Master module #: 1

Summary of Contents for P130 SMON

































































































































































Search results

Summary of Contents for P130 SMON

Reviews:

Related manuals for P130 SMON

Brands by name

Popular brands

Avaya P130 SMON, User Manual

Search results

Summary of Contents for P130 SMON

Reviews:

Related manuals for P130 SMON

Brands by name

Popular brands