manualshive.com logo in svg

Avaya P130 SMON, User Manual, Page: 126 / 160

Share
Download
Avaya P130 SMON User Manual Download Page 126

Chapter 6        Avaya P130 CLI

112

 Avaya P130 User’s Guide

Event 1054 is active, owned by amir
Description is event for monitoring amir's co
Event firing causes log and trap to community public, last 
fired 0:0:0  

Show rmon statistics Command

Use the show rmon statistics command to show the RMON statistics counters for a 
certain interface number according to the MIB-2 interface table numbering scheme.

The syntax for this command is:

show rmon statistics

 <Interface Number>

Example:

P130-N> show rmon statistics 1026

statistics

Interface 1026 is active, owned by Monitor
Monitors ifEntry.1.1026 which has
Received 26375085 octets, 222536 packets,
154821 broadcast and 53909 multicast packets,
0 undersize and 0 oversize packets,
0 fragments and 0 jabbers,
1 CRC alignment errors and 0 collisions,
# of dropped packet events (due to a lack of resources): 0
# of packets received of length (in octets):
64:94530, 65-127:85124, 128-255:25896,
256-511:10440, 512-1023:6057, 1024-1518:489,

Summary of Contents for P130 SMON

































































































































































Reviews:

No comments