Avaya P130 SMON User Manual Download Page 96 | Manualshive

Page: 96 / 160

background image

Chapter 6 Avaya P130 CLI

82

Avaya P130 User’s Guide

Spanning Tree Commands

Show spantree Command

Use the

show spantree

command to display spanning-tree information.

The syntax for this command is:

show spantree

[<mod_num>[/<port_num>]]

Example:

P130-N> show spantree
Spanning tree enabled

Designated Root: 00-40-0d-88-06-c8
Designated Root Priority: 32768
Designated Root Cost: 20
Designated Root Port: 1/1
Root Max Age: 20 Hello Time: 2

Bridge ID MAC ADDR: 00-40-0d-92-04-b4
Bridge ID priority: 32768

Port State    Cost   Priority
------ ------------- ---------- ------------
1 /1 Forwarding 20     128
1 /2 not-connected 20     128
1 /3 LAG-member 20     128
1 /4 LAG-member 20     128
1 /5 not-connected 20     128
1 /6 not-connected 20     128
etc...

mod_num

Module number

port_num

Number of the port on the module

«
...
94
95
96
97
98
...
»

Summary of Contents for P130 SMON

































































































































































Reviews:

No comments

Related manuals for P130 SMON

FLASH MEDIA SERVER 2-INSTALLING FLASH MEDIA SERVER...

Brand: MACROMEDIA Pages: 16

Brand: MAGIX Pages: 88

Brand: Sun Microsystems Pages: 38

CODESOFT Sentinel Print Pack

Brand: Techniques Avancees Pages: 50

Disk Array Administrator

Brand: Adaptec Pages: 139

AVC HD Player 5.7

Brand: Elecard Pages: 39

POLICY MANAGER PROXY 2.0 -

Brand: F-SECURE Pages: 24

Brand: GRASS VALLEY Pages: 216

Pro Tools M-Powered

Brand: DigiDesign Pages: 22

Phone Link Handbook

Brand: Palm Pages: 22

Brand: OfficeMate Pages: 39

TIVOLI SC23-8765-00

Brand: IBM Pages: 74

TC Chorus-Delay

Brand: TC Electronic Pages: 7

Brand: Fellowes Pages: 170

SNAP DEPLOY 3 - FOR WORKSTATION

Brand: ACRONIS Pages: 13

SNAP DEPLOY 3 - FOR WORKSTATION

Brand: ACRONIS Pages: 103

Brand: MACROMEDIA Pages: 860

ThinkCentre Edge 91

Brand: Lenovo Pages: 262

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands