Avaya P130 SMON User Manual Download Page 105

Page: 105 / 160

Chapter 6 Avaya P130 CLI

Avaya P130 User’s Guide

Set port vlan-binding-mode Command

Use the

set port vlan-binding-mode

command to define the binding method

used by ports.

The syntax for this command is:

set port vlan-binding-mode

[port_list] [value]

Example:

P130-1# set port vlan-binding-mode 1/5-15 static
Set Port vlan binding method:1/5
Set Port vlan binding method:1/6
.

Show port vlan-binding-mode Command

Use the

show port vlan-binding-mode

command to display port vlan binding

mode information.

The syntax for this command is:

show port vlan-binding-mode

Example:

P130-N> show port vlan-binding-mode
port 1/1 is statically bound
port 1/2 is statically bound
etc.

port_list

module and ports to bundle (format: module/port)

value

static

- the port supports only the egress VLAN list as

configured

bind-to-configured

- the port support the whole range of

VLANs on the device

Summary of Contents for P130 SMON

































































































































































Search results

Summary of Contents for P130 SMON

Reviews:

Related manuals for P130 SMON

Brands by name

Popular brands

Avaya P130 SMON, User Manual

Search results

Summary of Contents for P130 SMON

Reviews:

Related manuals for P130 SMON

Brands by name

Popular brands