Avaya P130 SMON User Manual Download Page 89

Page: 89 / 160

Chapter 6 Avaya P130 CLI

Avaya P130 User’s Guide

Example:

These examples show how to use the set port flowcontrol command set:

P130-1# set flowcontrol receive 5/1 on
Port 5/1 flow control receive administration status set to on
(port will require far end to send flowcontrol)
P130-1#

P130-1# set flowcontrol send 5/1 off
Port 5/1 flow control send administration status set to off
(port will send flowcontrol to far end)
P130-1#

Set port auto-negotiation-flowcontrol-advertisement Command

Use the

set auto-negotiation-flowcontrol-advertisement

command to

set the flowcontrol advertisement for a Gigabit port when performing
autonegotiation.

The syntax for this command is:

set port auto-negotiation-flowcontrol-advertisement

<mod_num>/<port_num> {no-flowcontrol | asym-tx-only | sym-only
| sym-and-asym-rx}

Example:

P130-1# set port auto-negotiation-flowcontrol-advertisement
1/51 asym-tx-only
Port 1/51 pause capabilities was set

mod_num

Module number

port_num

Number of the port on the module

no-flowcontrol

The port will advertise no pause capabilities

asym-tx-only

The port will advertise asymmetric Tx pause capabilities only

sym-only

The port will advertise symmetric pause capabilities only

sym-and-
asym-rx

The port will advertise both symmetric and asymmetric Rx
pause capabilities.

Summary of Contents for P130 SMON

































































































































































Search results

Summary of Contents for P130 SMON

Reviews:

Related manuals for P130 SMON

Brands by name

Popular brands

Avaya P130 SMON, User Manual

Search results

Summary of Contents for P130 SMON

Reviews:

Related manuals for P130 SMON

Brands by name

Popular brands