Avaya P130 SMON User Manual Download Page 73

Page: 73 / 160

Chapter 6 Avaya P130 CLI

Avaya P130 User’s Guide

Copy module-config tftp Command

Use the

copy module-config tftp

command to upload the module-level

parameters from the current NVRAM running configuration into a file via TFTP.

The syntax for this command is:

copy module-config tftp

Example:

P130-1# copy module-config tftp c:\p130\switch1.cfg
192.168.49.10 5

Beginning upload operation ...
This operation may take a few minutes...
Please refrain from any other operation during this time.
For more information , use 'show tftp upload status' command

Copy tftp stack-config Command

Use the

copy tftp stack-config

command to download the stack-level

configuration from a saved file into the current NVRAM running configuration, via
TFTP.

The syntax for this command is:

copy tftp stack-config

Example:

P130-1# copy tftp stack-config c:\p130\switch1.cfg
192.168.49.10

File name (full path)

<ip>

The IP address of the host

<mod_num>

Module number

File name (full path)

<ip>

The IP address of the host

Summary of Contents for P130 SMON

































































































































































Search results

Summary of Contents for P130 SMON

Reviews:

Related manuals for P130 SMON

Brands by name

Popular brands

Avaya P130 SMON, User Manual

Search results

Summary of Contents for P130 SMON

Reviews:

Related manuals for P130 SMON

Brands by name

Popular brands