AUMA AC(V) 01.2, Manual

Page: 14 / 92

Description Designation
(process representation) Prm-Text-Def GSD file
Collective signal 03:
Contains the result of a disjunction (OR operation) of all faults.
The actuator cannot be operated. Fault (20) = "Bit: Fault"
Collective signal 02:
Contains the result of an OR disjunction of all warnings. Warning (21) = "Bit: Warnings"
Collective signal 04:
Contains the result of a disjunction (OR-operation) of the signals,
forming the "Not ready REMOTE" group.
The actuator cannot be operated from REMOTE. Not ready REMOTE (22) = "Bit: Not ready REMOTE"
The actuator is in off-time (e.g. stepping mode or reversing preven-
tion time). Operation pause active (23) = "Bit: Op. pause active"
The actuator is within the set stepping range. Start stepping mode (24) = "Bit: Start step mode"
Actuator is running (output drive is moving)
Hard wired collective signal consisting of signals:
●
(26) Running LOCAL
●
(27) Running REMOTE
●
(28)
Handwheel oper.
Actuator running (25) = "Bit: Actuator running"
Output drive rotates due to operation command from LOCAL. Running LOCAL (26) = "Bit: Running LOCAL"
Output drive rotates due to operation command from REMOTE. Running REMOTE (27) = "Bit: Running REMOTE"
Output drive rotates without electric operation command (manual
operation). Handwheel oper. (28) = "Bit: Running via handw."
The actuator is in an intermediate position e.g. neither in end posi-
tion OPEN nor in end position CLOSED. In intermediate pos. (29) = "Bit: In interm. position"
The failure behaviour is active. Failure behav. active (30) = "Bit: Failure behav. active"
Intermediate position 1 reached Intermediate pos. 1 (31) = "Bit: Intermediate pos. 1"
Intermediate position 2 reached Intermediate pos. 2 (32) = "Bit: Intermediate pos. 2"
Intermediate position 3 reached Intermediate pos. 3 (33) = "Bit: Intermediate pos. 3"
Intermediate position 4 reached Intermediate pos. 4 (34) = "Bit: Intermediate pos. 4"
Intermediate position 5 reached Intermediate pos. 5 (35) = "Bit: Intermediate pos. 5"
Intermediate position 6 reached Intermediate pos. 6 (36) = "Bit: Intermediate pos. 6"
Intermediate position 7 reached Intermediate pos. 7 (37) = "Bit: Intermediate pos. 7"
Intermediate position 8 reached Intermediate pos. 8 (38) = "Bit: Intermediate pos. 8"
A high signal (+24 V DC) is present at digital input 1. Input DIN 1 (39) = "Bit: Input DIN 1"
A high signal (+24 V DC) is present at digital input 2. Input DIN 2 (40) = "Bit: Input DIN 2"
A high signal (+24 V DC) is present at digital input 3. Input DIN 3 (41) = "Bit: Input DIN 3"
A high signal (+24 V DC) is present at digital input 4. Input DIN 4 (42) = "Bit: Input DIN 4"
A high signal (+24 V DC) is present at digital input 5. Input DIN 5 (43) = "Bit: Input DIN 5"
A high signal (+24 V DC) is present at digital input 6. Input DIN 6 (44) = "Bit: Input DIN 6"
Parameter not available Input DIN 7 (45) = "Bit: Input DIN 7"
Parameter not available Input DIN 8 (46) = "Bit: Input DIN 8"
No valid communication via fieldbus (despite available connection) FailState fieldbus (47) = "Bit: FailState fieldbus"
The actuator is controlled via the I/O interface (parallel). I/O interface (48) = "Bit: I/O interface"
Operation mode EMERGENCY is active (EMERGENCY signal was
sent). EMCY behav. active (49) = "Bit: EMCY behav.act."
Operation mode EMERGENCY stop is active (EMERGENCY stop
button pressed). EMCY stop active (50) = "Bit: EMCY stop active"
Operation mode Service (via Bluetooth) is active. Service active (51) = "Bit: Service active"
Actuator is interlocked. Interlock active (52) = "Bit: Interlock active"
Selector switch is in position Local control (LOCAL) or 0 (OFF). Sel. sw. not REMOTE (53) = "Bit: Sel. sw. not REMOTE"
Manual operation is active (handwheel is engaged); optional signal Handwheel active (54) = "Bit: Handwheel active"
14
Actuator controls
Commissioning AC(V) 01.2/AC(V)ExC 01.2 Profibus DP