manualshive.com logo in svg

Atlas Xenotest 440, Operating Instructions Manual

Share
Download
Atlas Xenotest 440 Operating Instructions Manual Download Page 12

Operating Manual Xenotest

®

 440

- 12 -

Inhalt/Content/Sommaire

3.4  

Water supply 

The Xenotest

®

 440 requires purified water for humidify

-

ing the test chamber. Purified water circulates in a closed 
pipe system which is fed from the internal 60-liter water 

tank. The water tank can either be refilled manually or 
connected to a water treatment system.

•   Connection: G 3/8 " (inch)
The purified water must have the following quality char

-

acteristics:

•   Conductance: < 5 μS/cm
•   pH value: 6 – 8
•   Max. silicate content: 0.2 ppm

 

NOTE – water quality

Poor water quality not only leads to poor test results  but 

also affects the function and life of the components in 
the instrument.

3 

Requirements for the installation site

3.5  

Transport

 

NOTE – Transport

The instrument may only be transported by experienced 

service personnel using suitable equipment. The instru

-

ment may not be lifted by the front or side doors for 
transport.

 

NOTE – lifting points (fig. 1)

The instrument may only be lifted at the lifting points
indicated in 

fig. 1

.

Fig. 1

Summary of Contents for Xenotest 440

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands