Associated 12-1015 User Manual Download Page 48

Page: 48 / 56

48 -

Model 12-1015 Users’ Manual Version 13.08

Associated Equipment Corp.

5043 Farlin Ave.

800-949-1472(US)

St. Louis, MO 63115

314-385-5178 (Outside US)

Pressing key once will scroll down to the ‘View last Test’

See Fig. 72.

4. Press key will proceed to display the last test results depends on the

type of test you had performed earlier. (Fig. 73)

5. To view the next page, press

or key to get to the page you want.

Some examples below are: (Figs. 74, 75, 76 & 77)

Figure 72

Figure 73

Figure 74

Figure 75

Select Menu

New: Clear Memory

Continue Testing

View last Test

Setup Menu

Then press [Enter].

Battery: Good

Measured: 406 CCA

Rating: 630 CCA

Volts: 12.45 V

Int. R: 6.72 mOhm

Life: 76%

Results: High Ohms

The grounding

resistance of the

engine or car

chassis is high.

Clean the cable

contacts or replace

cable if necessary.

Result: High Drop

Min. Volts: 8.56V

Volt Drop: High

Check starter relay,

battery terminals or

battery has aged.

Press [Exit] to main

menu.

Summary of Contents for 12-1015

























































Search results

Summary of Contents for 12-1015

Reviews:

Related manuals for 12-1015

Brands by name

Popular brands

Associated 12-1015, User Manual

Search results

Summary of Contents for 12-1015

Reviews:

Related manuals for 12-1015

Brands by name

Popular brands