Associated 12-1015 User Manual Download Page 21 | Manualshive

Page: 21 / 56

background image

-

21 -

Model 12-1015 Users’ Manual Version 13.08

Associated Equipment Corp.

5043 Farlin Ave.

800-949-1472(US)

St. Louis, MO 63115

314-385-5178 (Outside US)

Press key and the display will show: (Fig.26) below:

12. Referring to the Table list (Fig.25) basing on 80D26L, check the battery

type:  WET,  MF,  Sealed  MF  or  Closed  MF  (CMF)  as  each  category  has
different  CCA  ratings.  For  instance,  if  the  battery  is  a  Sealed  MF  (CMF)
then it is rated at 630 CCA.

Note:

WET -

Wet Cell Type

MF

-

Maintenance Free Type

SMF -

Closed or Sealed Maintenance Free

13. To enter the value 630, press key will increase the original value

of 500 (Fig.26) by step of 100 units to 600. Likewise use key to

increase the last two digits (00) to 30 by step of 5 units for each pressing.

(Fig. 27)

Figure 26

Figure 27

Input Battery Rating

Increase/decrease:

Single digit

⊳

By hundredth

500 CCA

Press [Enter] to

proceed.

Input Battery Rating

Increase/decrease:

Single digit

⊳

By hundredths

630 CCA

Press [Enter] to

proceed.

«
...
19
20
21
22
23
...
»

Summary of Contents for 12-1015

























































Reviews:

No comments

Related manuals for 12-1015

Brand: Major tech Pages: 8

Brand: Waltron Pages: 25

Brand: ParTech Pages: 14

Brand: Campbell Pages: 22

Brand: Campbell Pages: 32

Brand: Campbell Pages: 40

CR3000 Micrologger

Brand: Campbell Pages: 12

Brand: R.M. Young Pages: 8

Brand: Campbell Pages: 21

Brand: Mini Pages: 20

Brand: Magnet-physik Pages: 32

Brand: E-Mon Pages: 72

Brand: Sper scientific Pages: 56

Brand: kruss Pages: 115

Micropilot S FMR533

Brand: E+H Pages: 12

Brand: National Instruments Pages: 169

Brand: Teledyne Lecroy Pages: 3

Brand: Kirby Morgan Pages: 101

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands