Associated 12-1015 User Manual Download Page 18 | Manualshive

Page: 18 / 56

background image

-

18 -

Model 12-1015 Users’ Manual Version 13.08

Associated Equipment Corp.

5043 Farlin Ave.

800-949-1472(US)

St. Louis, MO 63115

314-385-5178 (Outside US)

7. If the surface charge is too great for the analyzer to handle, it will prompt

you with the instructions as shown: (Fig. 20) below.

8. Wait until the surface charge removal had completed, the analyzer will

advise as follows: (Fig.21) and then press key.

9. If there is no surface charge present, then it will straight away enter into

“Select Battery” menu screen as shown in Fig. 22

Figure 21

Figure 22

Figure 20

Battery surface

charge is present!

Turn the ignition

key to ON position.

Switch ON the

headlights to remove

surface charge.

Battery surface

charge has been

removed.

Turn ignition key to

OFF position.

Switch OFF the

headlights and then

press [Enter].

Select Battery

SLI (Wet Type)

AGM (Flat/Spiral)

[Enter] to proceed

«
...
16
17
18
19
20
...
»

Summary of Contents for 12-1015

























































Reviews:

No comments

Related manuals for 12-1015

Brand: JGR Pages: 12

System SourceMeter 2601B

Brand: Keithley Pages: 13

Brand: Keller-druck Pages: 8

VOLUTANK Petro 3003

Brand: Bartec Pages: 10

Brand: Aqua Lung Pages: 24

Brand: SATO KEIRYOKI Pages: 2

Brand: Omega Pages: 20

Brand: OHAUS Pages: 6

Brand: AKCP Pages: 16

Brand: Swann Pages: 106

Brand: SBS Pages: 17

Brand: Omega Pages: 22

Brand: Keysight Pages: 42

Brand: b&o Pages: 32

Brand: Kawai Pages: 16

NEO MP18X Series

Brand: MA Pages: 3

Brand: AlazarTech Pages: 64

Brand: JETI model Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands