Associated Research HYAMP 3240 Service Manual Download Page 53

Page: 53 / 77

© Associated Research 2017



Appendix A - Installation and Test Operator Information

Installation

1. Unpacking and Inspection

Your instrument ships in a custom foam insulated container. If the shipping carton is damaged, inspect the contents for visible

damage such as dents, scratches or a broken display. If the instrument is damaged, notify the carrier and Associated Research’s

customer care department. Please save the shipping carton and packing material for the carrier’s inspection. Our customer care

department will assist you in the repair or replacement of your instrument. Please do not return your product without first notify-

ing us and receiving an RMA (return material authorization) number. To receive an RMA number, please contact our

customer care department at

1-800-858-TEST (8378)

2. Safe Lifting and Carrying Instructions

Proper methods of lifting and carrying can help to protect against injury. Follow the recommendations below to ensure that

instruments are handled in a safe manner.

• Determine if the instrument can be lifted by one individual or requires additional support.

• Make sure that your balance is centered and your feet are properly spaced, shoulder width apart behind the instrument.

• Bend at the knees and make sure your back is straight.

• Grip the instrument with your fingers and palms and do not lift unless your back is straight.

• Lift up with your legs, not your back.

• Keep the instrument close to your body while carrying.

• Lower the instrument by bending your knees. Keep you back straight

3. Contents of the Carton

DESCRIPTION

AR PART NUMBER

HYAMP Series Instrument

3240

High Current Output Cable

38489

High Current Return Cable

38490

Fuse

37780

USB Cable AB-Type 1.8m

39066

Line Cord

33189 Standard

2U Rack Mount Handle (Qty 2)

38794

2U Rack Mount Bracket (Qty 2)

38793

Adaptor Box

38549 For Rack Mount Handle

38482 Standard

38075

Screw M4 x 12mm FHMS (Qty 4)

38549 For Rack Mount Handle

The Line Cord listed is American. Other combinations of the Line Cord are available upon request.

Summary of Contents for HYAMP 3240














































































Search results

Summary of Contents for HYAMP 3240

Reviews:

Related manuals for HYAMP 3240

Brands by name

Popular brands

Associated Research HYAMP 3240, Service Manual

Search results

Summary of Contents for HYAMP 3240

Reviews:

Related manuals for HYAMP 3240

Brands by name

Popular brands