Arthrex DrillSaw Sports 400 User Manual Download Page 47

Page: 47 / 52

DrillSaw Sports 400™ System

User’s Guide

DFU-0253-4r0_fmt_en-US

Page 41 of

Electromagnetic Emissions

Table 21

Guidance and Manufacturer's Declaration - Electromagnetic

Emissions

The DrillSaw Sports 400 System is intended for use in the electromagnetic environment
specified below. The customer or the user of the DrillSaw Sports 400 System should
ensure that it is used in such an environment.

Emissions test

Compliance Electromagnetic environment – guidance

RF emissions
CISPR 11

Group 1

The DrillSaw Sports 400 System uses RF energy
only for its internal function. Therefore, its RF
emissions are very low and not likely to cause any

interference with nearby electronic equipment.

RF emissions
CISPR 11

Class A

The DrillSaw Sports 400 System is suitable for use
in all establishments other than domestic and

those directly connected to the public low-voltage
power supply network that supplies buildings
used for domestic purposes.

Harmonic
emissions

IEC 61000-3-2

Class A

Voltage
fluctuations/

flicker emissions
IEC 61000-3-3

Complies

Summary of Contents for DrillSaw Sports 400





















































Search results

Summary of Contents for DrillSaw Sports 400

Reviews:

Related manuals for DrillSaw Sports 400

Brands by name

Popular brands

Arthrex DrillSaw Sports 400, User Manual

Search results

Summary of Contents for DrillSaw Sports 400

Reviews:

Related manuals for DrillSaw Sports 400

Brands by name

Popular brands