ARM V2M-Juno r2 Technical Reference Manual Download Page 96

Page: 96 / 150

Table 4-12 SYS_MISC Register bit assignments

Bits

Name

Function

[31:20]

Reserved. If you write to this register,
you must write all zeros to these bits. If
you read this register, you must ignore
these bits.

[19]

SWINT

Event output to daughterboard. See
your daughterboard documentation for
more information specific to your
board.

[18:14]

Reserved. If you write to this register,
you must write all zeros to these bits. If
you read this register, you must ignore
these bits.

[13]

nDBDET

Detect fitted daughterboard:

0b0

Daughterboard not present.

0b1

Daughterboard present.

[12:0]

Reserved. If you write to this register,
you must write all zeros to these bits. If
you read this register, you must ignore
these bits.

Related concepts

4.3.1 APB system register summary

on page 4-89

4.3.10

SYS_PCIE_CNTL Register

The SYS_PCIE_CNTL Register characteristics are:

Purpose

Error signal from PCIe switch and reset signal to PCIe Express slots.

Usage constraints

There are no usage constraints.

Configurations

Available in all V2M-Juno r2 motherboard configurations.

The following figure shows the bit assignments.

Reserved

2 1

PCIE_nPERST

PCIE_RSTHALT

Figure 4-11 SYS_PCIE_CNTL Register bit assignments

The following table shows the bit assignments.

4 Programmers Model

4.3 APB system registers

ARM 100114_0200_03_en

4-96

Non-Confidential

Summary of Contents for V2M-Juno r2






















































































































































Search results

Summary of Contents for V2M-Juno r2

Reviews:

Brands by name

Popular brands

ARM V2M-Juno r2, Technical Reference Manual

Search results

Summary of Contents for V2M-Juno r2

Reviews:

Brands by name

Popular brands