ARM V2M-Juno r2 Technical Reference Manual Download Page 73

Page: 73 / 150

A file of the form

pms_vxxx.bin

Binary configuration file for the

Power Management IC

(PMIC) on

the V2M-Juno r2 motherboard.

tapid.arm

file

Contains JTAG ID codes for the V2M-Juno r2 motherboard and
LogicTile daughterboards.

The following example shows a typical V2M-Juno r2 motherboard configuration

board.txt

file.

BOARD: HBI0262

TITLE: Motherboard configuration file

[MCCS]

MBBIOS mbb_v117.ebf ;MB BIOS IMAGE

[FPGAS]

MBIOFPGA: io_v114.bit ;MB IOFPGA

[PMIC]

MBPMIC: pms_v103.bin ;MB PMIC

[OSCCLKS]

TOTALOSCCLKS: 11

OSC0: 50.O ;OSC0 Juno SYSREFCLK (System clock)

OSC1: 50.O ;OSC1 Juno AONREFCLK (Always on)

OSC2: 50.O ;OSC2 Juno PXLREFCLK (HS pixel clock)

OSC3: 50.O ;OSC3 Juno PXLCLKIN (LS pixel clock)

OSC4: 2.11 ;OSC4 Juno I2SCLK (Audio)

OSC5: 50.O ;OSC5 Juno SMCMCLK (Static memory)

OSC6: 50.O ;OSC6 Juno CA53_REF_CLK (RSVD)

OSC7: 50.O ;OSC7 Juno CA72 REF_CLK (RSVD)

OSC8: 50.O ;OSC8 Juno GPU REF_CLK (RSVD)

OSC9: 50.O ;OSC9 IOFPGA BOOT (RSVD)

OSC10: 24.O ;OSC10 IOFPGA UART (RSVD)

OSC11: 7.37 ;OSC11 Juno UARTCLK (UART clock)

Related concepts

2.5.1 Overview of clocks

on page 2-28

3.3.4

Contents of the

SITE1

directory

The

SITE1

directory contains files that relate to the Juno r2 SoC and to external memory on the

V2M-Juno r2 motherboard that the Juno r2 SoC can access.

The

SITE1

subdirectory contains an

HBI0262D

subdirectory that matches the HBI code of the V2M-Juno

r2 motherboard. The

HBI0262D

subdirectory contains the following files:

board.txt

file

Contains configuration information for the SCC registers in the Juno r2 SoC.

images.txt

file

Defines the files that the MCC loads into external memory during configuration.

The following example shows a typical V2M-Juno r2 motherboard

board.txt

file in the

SITE1

Summary of Contents for V2M-Juno r2






















































































































































Search results

Summary of Contents for V2M-Juno r2

Reviews:

Brands by name

Popular brands

ARM V2M-Juno r2, Technical Reference Manual

Search results

Summary of Contents for V2M-Juno r2

Reviews:

Brands by name

Popular brands